                   .:                     :,                                          
,:::::::: ::`      :::                   :::                                          
,:::::::: ::`      :::                   :::                                          
.,,:::,,, ::`.:,   ... .. .:,     .:. ..`... ..`   ..   .:,    .. ::  .::,     .:,`   
   ,::    :::::::  ::, :::::::  `:::::::.,:: :::  ::: .::::::  ::::: ::::::  .::::::  
   ,::    :::::::: ::, :::::::: ::::::::.,:: :::  ::: :::,:::, ::::: ::::::, :::::::: 
   ,::    :::  ::: ::, :::  :::`::.  :::.,::  ::,`::`:::   ::: :::  `::,`   :::   ::: 
   ,::    ::.  ::: ::, ::`  :::.::    ::.,::  :::::: ::::::::: ::`   :::::: ::::::::: 
   ,::    ::.  ::: ::, ::`  :::.::    ::.,::  .::::: ::::::::: ::`    ::::::::::::::: 
   ,::    ::.  ::: ::, ::`  ::: ::: `:::.,::   ::::  :::`  ,,, ::`  .::  :::.::.  ,,, 
   ,::    ::.  ::: ::, ::`  ::: ::::::::.,::   ::::   :::::::` ::`   ::::::: :::::::. 
   ,::    ::.  ::: ::, ::`  :::  :::::::`,::    ::.    :::::`  ::`   ::::::   :::::.  
                                ::,  ,::                               ``             
                                ::::::::                                              
                                 ::::::                                               
                                  `,,`


https://www.thingiverse.com/thing:62800
GoPro customizable mounts, and a library to expand by MoonCactus is licensed under the Creative Commons - Attribution - Non-Commercial license.
http://creativecommons.org/licenses/by-nc/3.0/

# Summary

This is a flexible library for GoPro mounts. It is also customizer-friendly so you can design your very own mounts and print them directly. 

In the predefined shapes, you'll get the basic 2- and 3-arm mounts (to build upon), but it also features useful extensions such as handlebar / seat post / threaded rod mounts and options. Check the pictures, and the customizer!

# Instructions

Chances are that you will never find the appropriate mount. So use the customizer to bulid it to your need: http://www.thingiverse.com/apps/customizer/run?thing_id=62800  
The OpenScad module was also designed to be included in other designs.

One of the attached images explains most of the settings. The current options are:  
- the regular "double arm" connector  
- the regular "triple arm" connector, with the optional locking nut  
- an optional "extruded" extension arm in between the two ends   
- a generic clamp for bars and handlebars  
- a generic orentable mount for any threaded rod, with optional captive nut  
The latter can be given an angle. If it is 80-90Â° then the rod can be made through the mount, and you can add a "third" leg to your mount (eg in the middle of the threaded rod to make it both sturdy and stable for long rods for example, see the pics). You could even build a motorized pan/slider out of this.  
   
I will probably add extensions with time so following this object is the way to go if you need to know when. Feel free to ask for some more, so I can include them here. Planned are regular camera screw mount and flash mount.  
The naked 2- and 3-arm mounts are useful to protect your existing bits while they are not used. Just mount them so you can leave a screwed bolt without either losing the nut nor breaking an arm as I did more than once.  
I tried to fine-tune the gopro 2- and 3-arm mounts as some other designs were a bit fuzzy on this. Still, you can fine tune the values if you really want or need it in the last tab of the customizer.  
Programmers will find more comments & usage in the source code  
Cheers  
Jeremie